LED雷达感应吸顶式LED声控带弹簧感应开关红外线感应批发

人体感应开关说明书

产品简介：

基于红外技术的自动控制，灵敏度高，可靠性高，智能化，人性化，

本开关单极性设计，可直接替换遥控开关，手动开关，声控开关，

摸开关。无需改动原有布线，使用方便，可接各类灯具，排风扇等负

载。

适用范围：

本开关能负载白炽灯(灯泡)和节能灯LED灯环形灯管，日光灯等灯源，广泛适用于:宾馆、旅馆、办公室、工厂仓库、住宅小区等处的车库、楼道、走道、出入口、卫生间、电梯间等公共场所,配套灯具使用。是照明开关的最佳选择。

功能特点：

1.     全自动感应

人来灯亮，延时一定时间后，人离灯熄。节能环保。

2.     自动测光

3.     应用光敏控制,白天或强光下不感应,夜间或弱光下可感应.（也可做全天能感应的）

4.     自动延时

开关在接通后，如有人在开关感应范围内活动则一直接通。若人离开感应范围则按最后离开前的时间为基准点，开始延时，（延时时间见技术参数）为准，本开关不可调时调光。延时时间为本开关通过调电阻设定的时间为准.一般为20秒-40秒左右)

技术参数：

产品型号:AD01-R1

产品规格：75X38X28MM

工作电压:AC180V-240V(50/60HZ)

输出方式：继电器

负载功率:200W

感应距离：3-5米

感应角度：120度

启动亮度L：L＜5Lux（相当于晴天天刚亮时的天空亮度）、

延时时间：20-40秒

适用光源：白炽灯，节能灯，LED灯，日光灯，环形灯管等各种灯具。

使用说明：

1.       请按外壳上的接线图按装好开关,通电后一分钟为初始化时间,在初始化时间内开关通断为不定态,会连续闪三下,一分钟后进入正常工作状态,如白天检查开关是否正常,可用手盖住或用黑色物档住开关,使光线变暗,即可导通灯亮.

2.       延时及感光度为出厂时设定延时的时间和光度为准(具体见技术参数)本开关不可调节延时时间和光度.

3.       安装本开关时,请不要将开关装在强光直射及冷热气流进出口的位置,不宜装在噪声太大的环境下使用.否则会因误报信号而灯亮,不能达到节能效果.

4.       本开关允许并联接入,但必须要注意功率问题,不可大于产品规定的负载.本开关对所标负载功率均测试正常,低于所标负载功率可延长开关的使用寿命.

注意事项：

1.       安装时请断开电源,确保安全.

2.       禁止超过功率范围的适用.

3.       不能安装在水淋到的位置.

4.       探测距离随环境温度的变化而变化。夏季探测距离比较短，（与人体温度接近时最为明显），冬季探测距离比较远。

5.       不能安装在低于-20度和高于60度的位置。

6.       请不要安状在太阳直射的位置。

7.       建议不要安装在有活动物体的位置。

售后服务:

凡在本公司购买的产品均可保修18个月.若本产品在购买后的1个月内性能出现问题,且无外观损坏,划花,可直接更换新的产品.

下列情况下不属于保修范围:

1.       未按说明书要求安装,使用,维护,保管导致的产品故障或损坏.

2.       己经超出保修期限的.

3.       意外因素或为人行为导致产品损坏,如输入不适合电压,负载超出规定功率.高温,进水,摔坏,不按接线图上指示按装而烧坏产品等.

本产品己经广东省中山市古镇艾迪灯饰电器厂检验合格.请放心购买使用!

                 制造商：广东中山市古镇艾迪灯饰电器厂

                 售后保修电话:13421466186

                 客服电话：15800142081

                 质量监督电话:13715566621

                 地址:广东省中山市古镇海洲螺沙工业区一号

A human body induction switch.

Product introduction:

Automatic control, based on infrared technology has the advantages of high sensitivity, high reliability, intelligent, humanization,

The switch unipolar design, can be directly replace remote control switch, manual switch, control switch,

Touch switch. No need to change the original wiring, easy to use, can meet all kinds of lamps and lanterns, exhaust fan and other negative

Load.

Scope of application:

This switch can load the incandescent lamp (bulb) and LED light annular lamp, fluorescent lamps and other light source, widely used in hotels, hotel, office,: factory warehouse, residential area, garage, corridor, corridors, entrance, bathroom, elevators and other public places, auxiliary lamps use. Is the best choice of the lighting switch.

Function characteristics:

1 automatic induction

People to light, after a certain period of time delay, people from the lights out. Energy saving and environmental protection.

2 automatic metering

3 application of photosensitive control, daytime or glare not induction, night or can be induced under weak light. (can also be used throughout the day can induction)

4 automatic delay

Switch connected in, if people in the switch in the induction range has been switched on. If people leave the sensing range according to the final before leaving time as a reference point, start delay (delay time, technical parameters.) as the standard, the switch can not be adjusted according to the light. The delay time for the switch through the adjustable resistor to set the time is. For 20 seconds -40 seconds)

Technical parameters:

Product type: HY01-01

Product specifications: 75X38X28MM

Working voltage: AC180V-240V (50/60HZ)

Output mode: relay

The load power: 200W

The induction distance: 3-5 m

Induction angle: 120 degrees

Start the brightness of L:L < 5Lux (equivalent to the sunny day at dawn in the sky brightness),

Delay time: 20-40 seconds

Application: incandescent lamp, energy saving lamp, LED lamp, fluorescent lamp, circular lamp tube, lamp.

Instructions for use:

1 please according to the wiring diagram on the housing install the switch, after electrify a minute for initialization time, the on-off switch for unsteady at initialization time, continuous flash three, enter the normal working state after a minute, as day to check whether the switch is normal, usable hand cover or black fabric up switch, so that the dark, can guide light.

The 2 delay and the sensitivity to the factory set delay time and photometric prevail (see specific technical parameters) this switch can not adjust the time delay and luminosity.

3 the installation of the switch, please do not switch is arranged on the direct sunlight and cold and hot air import and export position, should not be used on too much noise environment. Otherwise they will be false alarm signal lights, can not achieve the effect of saving energy.

4 this switch allows parallel access, but must pay attention to power, load cannot be greater than the product requirements. This switch to standard load power of both tests are normal, below the standard can extend the service life of the switch power.

Matters needing attention:

1 when installed, please disconnect the power supply, to ensure safety.

The 2 forbidden to apply more than power range.

3 can not be installed in the water to the position.

4 detection distance along with the change of environmental temperature changes. Summer detection distance is short, (close to the body temperature was the most significant in winter), detection distance is far away.

5 can not be installed in the lower -20 and higher than 60 degrees position.

6 please don't ANN in the sun position.

7 installation is not recommended in the active object position.

After-sale service.

Where to buy the company's products can be guaranteed for 18 months. If the product in 1 months after the purchase of the performance problems, and the appearance of damage, scratching, can be directly replaced with new products.

The following case does not belong to the scope of warranty:

1 not according to the specifications for installation, use, maintenance, custody of product failure or damage.

2 has been beyond the warranty period.

The 3 accident factors or human behavior damage to the product, if the input is not suitable for voltage, load exceeds the prescribed power at high temperature, water, broken, not according to the wiring diagram indicates the installation and burnt products.

This product has been the ancient town of Zhongshan City, Guangdong Province, Addie Lighting & Electric Appliance Factory Inspection. Please rest assured that the use of purchase!

Manufacturer: Guangdong Zhongshan Addie Lighting Electrical Appliance Factory

Telephone customer service warranty: 13421466186

Customer service telephone: 15800142081

Quality supervision of telephone: 13715566621

Address: Zhongshan City Guangdong Province Haizhou Guzhen Town Luo sand Industrial Zone No.

.